Hunter-fan 44360 Bedienungsanleitung Seite 1

Form# 42710-0120091204©2009 Hunter Fan Co.Set & $aveSet & $aveSet & $aveInstallation andOperation ManualModel44360ProgrammableThermostatEn

10G RC RH Y Wif your existing thermostat is marked...label the wire with this sticker:G / FGGW / H / BW/BW/BY / C* / M / OY/0Y/0RC / VCRCRCRH / R / VR

114. Using the provided stickers, label each wire according to the Wire Labels chart. (If the terminals are not labeled, contact a qualied HVAC tech

12W/BRCGY/0Y1

13INSTALLING THE THERMOSTATINSTALLING THE WALL PLATE1. Remove the wall plate from the new thermostat by pressing the release tab on the bottom of the

14WRCYG

154. Remove the wall plate and drill two 3/16” holes where marked. 5. Tap the plastic anchors into the holes until they are ush with the wall. (Do

16GRC RHY/0W/BRCGY1Y/0W/BY1Terminal Shield

17INSTALLING THE THERMOSTAT, CONT.CONNECTING THE WIRES1. Loosen, but do not remove, the terminal screws. Note: A jumper wire has been provided, conne

18DISABLEENABLERECOVERYHGHEW/B Y/O RH RC GSYSTEM TYPESTDHPY1FAN OPTIONAMHEAT4TThermostat CoverSystem SwitchFan Switch

19ATTACHING THE THERMOSTATLift the thermostat cover and set the SYSTEM switch to OFF and the FAN switch to AUTO. 1. Fan option - Locate the HE/HG swi

2

2012front coverTab

214. Place the top of the thermostat over the two tabs on the wall plate. Press the thermostat onto the wall plate and press to snap the bottom tab i

22reset

23The default setting of the thermostat is Fahrenheit (Fo). (NOTICE: CHANGING THIS SETTING WILL RESET THE THERMOSTAT TO FACTORY DEFAULT PROGRAMS.)To c

24day/timeAMPMprogram

25The default for this thermostat setting is in a 12 hour format. You can change the format to 24 hour format by pressing DAY/TiME and then pROGRAM. T

26AMHEAT4T

27This thermostat gives you the ability to program up to 4 custom temperature settings per day or utilize pre-programmed settings. For manual operatio

28AMHEAT2TH

291. MANUAL OPERATION / OVERRIDEMany people prefer to operate their thermostats manually, adjusting settings as needed. You can either temporarily ove

3Table of ContentsImportant Information ... 5Tools ...

30hold/returnsystemoffheatcoolHOLD

312. PERMANENT OVERRIDEIf you want to permanently override all settings and adjust the thermostat manually:1. Press HOlD/RETURN until the Hold icon ap

32hometodayHOME TODAY

333. HOME TODAY OVERRIDE Overrides the programmed settings during a time you would not normally be home. Pressing Home Today during the rst or s

34Set Temp

35METHODS OF OPERATION4. VACATION OVERRIDEOverrides the programmed settings for a set amount of days. The rst number in Vacation Override mode indic

3610 pm8 am6 amProgram 1Heat : 68o F (20o C)Cool : 78o F (26o C)Program 2Heat : 60o F (16o C)Cool : 85o F (29o C)Program 3Heat : 68o F (20o C)Cool : 7

375. DEFAULT PROGRAMSBy using the pre-programmed settings, this thermostat can save you money by optimizing energy usage in heating and cooling.Refer

38AMPMprogramhold/returnsystemoffheatcool

396. CREATING CUSTOM PROGRAMS• Program times can be set in 10 minute increments.• Program temperature can be set in increments of 1o F (1o C).• Aft

4Congratulations!Thank you for choosing a Hunter programmable thermostat. Your new Hunter thermostat will provide years of reliable service and year-r

40AMPMHEAT COOL21 3 4M T W TH F SA SUprogramhold/returnsystemoffheatcool

413. Press Up or DOwN to change the hour. Press pROGRAM to save the hour and adjust the minute setting. 4. Press Up or DOwN to change the minute. Pr

42filterFILTER

43ICONS AND FEATURES1. INDIGLO® night-light - will backlight the display for easy viewing in the dark. Press any button to illuminate the light. (I

44energyUsage TodayMinHr

45ICONS AND FEATURES, CONT.3. Energy – calculates energy usage. Press to display the total operation time for heat and air conditioning for today,

46HEAT COOLsystemoffheatcoolreset

475. Span setting mode – allows you to adjust the system ON/OFF cycle rate. The default setting is 2 (the system cycles ON or OFF when the temperatur

48STAGE 1PMCOOL4MSTAGE 2

496. Low battery warning – indicates two stages of battery power shortage. When the batteries are detected as weak, the icon will ash until new AA

5This thermostat is designed to work on the followingheating and cooling systems:Gas – Standing PilotGas – Electronic IgnitionGas – Fired BoilersGas –

50hold/return

517. Auto recovery – allows heating and cooling systems to gradually recover from an energy-saving setpoint temperature to a comfort setpoint tempera

52

538. Error mode – indicates an unexpected battery problem. The screen will ash an ERR message and shut your system off until the batteries are repla

541. Temperature Range2. Compressor ProtectionAfter the system stops running in cooling mode, there will be a 3.5 minute delay before it can be resta

551. My display will not come on. 1 a. Check batteries and battery connections. 1 b. Reset the thermostat. ...

565. My heating or cooling will not turn on or off. 5 a. Check the Heat/Cool function switch to ensure it is set to the desired position. 5 b. Wai

577. My system continues to operate when the thermostat is in the off position. 7 a. Replace unit. 7 b. Check your system for proper wiring...

58Is there help on the web? Yes. Visit http://www.hunterfan.com for more information. ...

6This thermostat includes two #8 slotted screws and two wall anchors for mounting.To install your new thermostat, you will need the following supplies

7NOTICE! Do not disconnect the wires from the existing thermostat before reading these instructions. The wires must be labeled prior to removal to ens

8YRCGWYRCGW

91. Turn the system power OFF from the existing thermostat. Turn the power to the HVAC system OFF at the main power panel or at the furnace. (Failu